VERSION ""


NS_ : 
	NS_DESC_
	CM_
	BA_DEF_
	BA_
	VAL_
	CAT_DEF_
	CAT_
	FILTER
	BA_DEF_DEF_
	EV_DATA_
	ENVVAR_DATA_
	SGTYPE_
	SGTYPE_VAL_
	BA_DEF_SGTYPE_
	BA_SGTYPE_
	SIG_TYPE_REF_
	VAL_TABLE_
	SIG_GROUP_
	SIG_VALTYPE_
	SIGTYPE_VALTYPE_
	BO_TX_BU_
	BA_DEF_REL_
	BA_REL_
	BA_DEF_DEF_REL_
	BU_SG_REL_
	BU_EV_REL_
	BU_BO_REL_
	SG_MUL_VAL_

BS_:

BU_:
VAL_TABLE_ error_lilst 93 "Encoder LOS" 76 "Insul Resist Low" 69 "External Supply Range" 68 "VCL Run Time Error" 66 "Diagnostic Mode" 65 "Program Mode" 64 "No CAN from Primary" 62 "Fault from Primary" 61 "Motor Type Changed" 59 "Low Cell Fault" 58 "Charge Plugged In" 57 "Motor Over Temp" 56 "E7 Comm Error" 55 "Program Mode" 54 "No CAN from Secondary" 53 "Software Violation" 52 "Fault from Secondary" 51 "BMS CAN Communication Fault" 49 "Parameter Change Fault" 46 "EEPROM Failure" 45 "Pot Low Overcurrent" 44 "Pot2 Wiper Low" 43 "Pot2 Wiper High" 42 "Throttle Wiper Low" 41 "Throttle Wiper High" 39 "Main Contactor Not Closed" 38 "Main Contactor Welded" 37 "Motor Open" 36 "Encoder Fault" 31 "Main Open/Short" 29 "Motor Temp Sensor Fault" 28 "Motor Temp Hot Cutback" 25 "5V Supply Failure" 24 "Overvoltage Cutback" 23 "Undervoltage Cutback" 22 "Controller Overtemp Cutback" 18 "Severe Overvoltage" 17 "Severe Undervoltage" 14 "Precharge Failed" 13 "Current Sensor Fault" 12 "Controller Overcurrent" ;
VAL_TABLE_ amps_data 33 "Description for the value '0x21'" 32 "Description for the value '0x20'" 31 "Description for the value '0x1F'" 30 "Description for the value '0x1E'" 29 "Description for the value '0x1D'" 28 "Description for the value '0x1C'" 27 "Description for the value '0x1B'" 26 "Description for the value '0x1A'" 25 "Description for the value '0x19'" 24 "Description for the value '0x18'" 23 "Description for the value '0x17'" 22 "Description for the value '0x16'" 21 "Description for the value '0x15'" 20 "Description for the value '0x14'" 19 "Description for the value '0x13'" 18 "Description for the value '0x12'" 17 "Description for the value '0x11'" 16 "Description for the value '0x10'" 15 "Description for the value '0xF'" 14 "Description for the value '0xE'" 13 "Description for the value '0xD'" 12 "Description for the value '0xC'" 11 "Description for the value '0xB'" 10 "Description for the value '0xA'" 9 "Description for the value '0x9'" 8 "Description for the value '0x8'" 7 "Description for the value '0x7'" 6 "Description for the value '0x6'" 5 "Description for the value '0x5'" 4 "Description for the value '0x4'" 3 "Description for the value '0x3'" 2 "Description for the value '0x2'" 1 "Description for the value '0x1'" 0 "Description for the value '0x0'" ;


BO_ 1537 AC1239_Status_1: 8 Vector__XXX
 SG_ motor_amps : 39|16@0- (0.1,0) [-500|500] "A" Vector__XXX
 SG_ motor_volt : 55|16@0+ (0.1,0) [0|1000] "v" Vector__XXX
 SG_ motor_temp : 23|8@0- (1,0) [-200|200] "C" Vector__XXX
 SG_ motor_rpm : 7|16@0+ (1,0) [0|8000] "" Vector__XXX
 SG_ motor_controller_temp : 31|8@0- (1,0) [-200|200] "C" Vector__XXX

BO_ 1538 AC1239_Status_2: 7 Vector__XXX
 SG_ brake_light_bit : 51|1@0+ (1,0) [0|10] "" Vector__XXX
 SG_ reverse_bit : 50|1@0+ (1,0) [0|10] "" Vector__XXX
 SG_ regen_bit : 49|1@0+ (1,0) [0|10] "" Vector__XXX
 SG_ economy_bit : 48|1@0+ (1,0) [0|10] "" Vector__XXX
 SG_ brake_input : 47|8@0+ (1,0) [0|10] "%" Vector__XXX
 SG_ throttle_input : 39|8@0+ (1,0) [0|100] "%" Vector__XXX
 SG_ controller_fault_secondary : 31|8@0+ (1,0) [0|1000] "" Vector__XXX
 SG_ controller_fault_primary : 23|8@0+ (1,0) [0|1000] "" Vector__XXX
 SG_ motor_stator_frequency : 7|16@0+ (1,0) [0|50000] "Hz" Vector__XXX



VAL_ 1538 controller_fault_primary 93 "Encoder LOS" 76 "Insul Resist Low" 69 "External Supply Range" 68 "VCL Run Time Error" 66 "Diagnostic Mode" 65 "Program Mode" 64 "No CAN from Primary" 62 "Fault from Primary" 61 "Motor Type Changed" 59 "Low Cell Fault" 58 "Charge Plugged In" 57 "Motor Over Temp" 56 "E7 Comm Error" 55 "Program Mode" 54 "No CAN from Secondary" 53 "Software Violation" 52 "Fault from Secondary" 51 "BMS CAN Communication Fault" 49 "Parameter Change Fault" 46 "EEPROM Failure" 45 "Pot Low Overcurrent" 44 "Pot2 Wiper Low" 43 "Pot2 Wiper High" 42 "Throttle Wiper Low" 41 "Throttle Wiper High" 39 "Main Contactor Not Closed" 38 "Main Contactor Welded" 37 "Motor Open" 36 "Encoder Fault" 31 "Main Open/Short" 29 "Motor Temp Sensor Fault" 28 "Motor Temp Hot Cutback" 25 "5V Supply Failure" 24 "Overvoltage Cutback" 23 "Undervoltage Cutback" 22 "Controller Overtemp Cutback" 18 "Severe Overvoltage" 17 "Severe Undervoltage" 14 "Precharge Failed" 13 "Current Sensor Fault" 12 "Controller Overcurrent" ;